Destiny 4100 Especificaciones Pagina 1

1DESTINY 4100Installation InstructionsK1106-1 2/99

10Retainer Clip(Note Position)Retainer SlotLockedUnlockedControl BoardControl Board1. Remove the cabinet door2. Remove the lock knockout from the cont

11Wiring DiagramTo HousePhonesFrom PhoneCompanyGreenRJ-31XPLUGRedWhen using smoke reset, programthe Smoke Power Trigger to output8 (aux relay) 043,008

12Wiring NotesGrounding: In UL installations where the Speaker Supervision option is enabled, grounding is notpermitted.If grounding, it is recommende

13System TerminalsHouse Phones: The R1 and T1 terminals provide telephone service to the house if the installationcontains an RJ-31X terminal block fo

14Auxiliary Relay: A programmable relay is available on the "RC", "RNC" , and "RNO" terminals. Use "RC"for r

15there is a modem to modem connection during upload or download.POWER LED: At the top right of the board is a red LED labeled "POWER" which

16Two Resistor Supervision: This wiring arrangement allows the system to detect and handle open loops and shorts asa trouble condition. Through progr

17ProgrammingSystem options are contained in EEPROM. Each programmable section of memory has a 4 digit location and athree digit value. To reduce th

18Quick StartKeypad connection: Connect a hardwire keypad to the keypad terminals on the control board, be certain toproperly match the colors as foll

19Using This Manual:Automated Locations: Automated Location prompt for specific information and automatically record theappropriate information into t

2

20System SetupZone 1-8System KeypadsSystem Board Inputs 1-8Local Phone PanicTwo Wire Smoke LoopWireless TransmittersZone 9Zone 27Zones 24 - 25Zones 10

21Programming ZonesThe device types for each zone on the Destiny 4100 are predefined. The device assignments are fixed andmay not be modified.Zones

22Zones 1 - 8: System ControllerAt default, all 8 system inputs are disabled. To enable a hardware input, enter a zone type in the zone typelocation.

23=RQH,QSXW:LUH6PRNH2SWLRQ /RFDWLRQ 'HIDXOW 1HZ9DOXH 'HIDXOW'HVFULSWLRQ=RQH7\SH   :RUG :RUG :RUG :RUG2SWLRQ 

24=RQH =RQH,QSXW7UDQVPLWWHU6HULDO ,QSXW7UDQVPLWWHU6HULDO2SWLRQ /RFDWLRQ 'HIDXOW 1HZ9DOXH 2SWLRQ /RFDWLRQ 'HIDXOW 1HZ9DOXH&

25Zones 18 - 23: Alarm Type Transmitters Continued=RQ H =R QH,QSXW7UDQVP LWWHU6HULDO ,QSXW7UDQVP LWWHU6HULDO2SWLRQ /RFDWLRQ 'HID

26Portable TransmittersType Description Value5801...4 button portable...

27=RQH,QSXW6\VWHP.H\SDGV2SWLRQ /RFDWLRQ 'HIDXOW 1HZ9DOXH±6WDWXV  ±0RQLWRU  ±)  ±  ±  

28Zone 29: Monitor Trouble ConditionsOption - A description of each option is available in the Glossary Location Value* Duration for recognition of A

29Automated Programming LocationsClear user codes 2-8...

3Dear Dealer/Installer:We appreciate your decision to use the Destiny 4100 for this installation. As a division of the Pittway Corporationand member

30VocabularyWord LocationAccess...024Account...025Alarm...222Alert...026Am.

31System Times And Other OptionsSystem Time Options - A description of each time is available in the Glossary Units Location DefaultEntry delay 1 (Not

32User Code + Digit FunctionsUser Code + Options Local phone/keypads Function Remote Phone FunctionFunction for User Code + 1...

33System Options - Group 4Options - Enter Total - A description of each option is available in the Glossary Location ValuePrevent access to Program M

34Extended Monitor Zone Type AssignmentZone Types - Enter Total for Extended Monitor A Location ValueExterior instant...

35Smoke Detector Low Battery WarningUpon detection of a low battery from a transmitting device assigned as a Fire zone type, the panel will start awar

36After the settling delay completes, the panel begins a window delay and startswatching for another on-board or 2-wire smoke zone trip. The period

37Reporting FormatReporting Options: Enter total - See Glossary for a description of each format Location ValueSilent Knight Slow...

38Report CodesReport Type Location ValueExterior Instant Central Station Report Code...0337...003_______Dialer Option...

39Report Type Location ValueAC Fail Central Station Report Code...0365...008_______Dialer Option...

4Software RevisionsCurrent software at time of printing:Control Panel: 1.01Bridge (Gate): 1.03EXP8: 1.01LED Keypad: 4.01Downloader 1.001.00 To 1.01 Pa

40Ademco Contact ID Report CodesAPEX Description Code Sent to Central Station ADEMCO DescriptionExterior instant...E 13

41Automatic Communicator TestingChoose to Report Daily, Weekly, or Monthly and enter the appropriate value Location ValueReport Daily...

42Two-Way Voice OptionsThis feature is not permitted in a UL installationVoice Only Options - Enter total ValueOne Digit Access...

43System TriggersEvent Location Output Location Option Location Time Option Default TimesAny alarm activation...0122.

44System Triggers OptionOption - Enter Total ValueActivation ActionDo Nothing...

45Glossary of TermsAccess code before arm: In this configuration, a full access code (arm/disarm code) must be entered to arm thesystem. Once armed,

46Button Functions: These are activations that are controlled by portable transmitters and/or keycombinations on keypads.Silence Day Zone: Cancels a

47Bypass Mode: To bypass individual zones, enter a valid full function code followed by the 9 digit.The system will speak "BYPASSED MODE, ENTER Z

48Clear EML and LTM: The Event Memory Log and Long Term memory can be cleared by entering 9898while in program mode.Clear Keypad Status: Under very un

49Display Open at Keypad: Used to show when specified zones are open. Typically, all internal zones (PIR's,Smoke Detectors) are not programmed t

5Table of ContentsSpecifications...7It

50Enable Two-way Callback:For this option to be used, at least one activation must be programmed to enable two-way voice/listen-in with the central st

51There are two different levels or types of extended monitor, A and B. Locations 0177and 0178 determine which zone types are to be monitored by each

52No Exterior Instant When enabled, this option will eliminate the exit delay on all exterior instant zonesExit Delay: following arming to either HOM

53Report Code: All events that initiate a communicator report are associated with a report code(based on zone type) that appears at the central statio

54Set Time and Date: After entering 9991 the system will prompt "Enter Eleven." The time, day, and dateare entered in the following format

55Speak Phone Number: To confirm programmed phone numbers, Enter the appropriate 9000 location and thenumber will be spoken. Special dialing feature c

56Touch Tone / This location determines the type phone service the panel uses for dialing. ProgramPulse Dial: 000 for touch-tone or 001 for rotary.Tr

57Disarm: Active when the panel is disarmed. The output is restored when the panel is armed.Access Code Entered: Output is activated when an access

58There are three security options associated with two-way callback, one digit access,full code access, and entering 0 to exit to keypad mode. If eit

59Zone type assignment: Auxiliary: Auxiliary zones are non-burglary zones designed to provide an automation,information, or service input to the syst

6Reporting Format...37Dialer Options...

60Interior Delay #2: Same as Exterior Delay #2 except active only in AWAY and NIGHT modeand no monitor is provided. Uses delay time #2.Panic: Panic

61This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires thefollowing statement for your informati

62Preparation of an evacuation plan Is of prime importance in fire prevention.Establish a household emergency evacuation plan in the event of fire. Re

63WARNINGTHE LIMITATIONS OF THIS ALARM SYSTEMWhile this System is an advanced wireless security system, it does not offer guaranteed protection agains

64ADEMCO LIMITED WARRANTYAlarm Device Manufacturing Company, a Division Of Pittway Corporation, and its divisions, subsidiaries and affiliates(`Seller

7SpecificationsElectrical: Voltage Input: 16.5 VAC 40 VA from supplied transformerExternal Speaker: 10 Watt minimum, 8W horn type - Ademco 713 or equi

8Speaker Output: 10 Watt internal siren driver with full speech10 Watt external siren driver with full speechDesigned for use with 8W, 10 watt minimum

9Items Included With the Control Panel:Please examine the contents of the shipping box for the following items:1 - Control Panel 1 - Lock, key, and re